Sunday, March 29, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 131

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 131



B0014 02, B0015 02, B0016 02, B0019 02, B0020 02, B0021 02, B0022 02, B0023 02



The air bag or retractor pretensioner control circuit is shorted to ground for 2 seconds.



B0014 04, B0015 04, B0016 04, B0019 04, B0020 04, B0021 04, B0022 04, B0023 04



The air bag or retractor pretensioner control circuit is open for 2 seconds.



B0014 0D, B0015 0D, B0016 0D, B0019 0D, B0020 0D, B0021 0D, B0022 0D, B0023 0D



The air bag or retractor pretensioner deployment loop resistance is greater than 4.2 ohm for 2 seconds.



B0014 0E, B0015 0E, B0016 0E, B0019 0E, B0020 0E, B0021 0E, B0022 0E, B0023 0E



The air bag or retractor pretensioner deployment loop resistance is less than 1.4 ohm for 2 seconds.



Action Taken When the DTC Sets



* The SDM requests the instrument cluster to illuminate the AIR BAG indicator.



* The SDM will store a DTC, however if an event occurs the system will still attempt deployments.



Conditions for Clearing the DTC



* The condition for setting the DTC no longer exists.



* A history DTC will clear once 100 malfunction-free ignition cycles have occurred.



Diagnostic Aid



Note: The following diagnostic aids apply for both current and history DTCs.



An incorrectly installed CPA or incorrectly seated connector can cause a shorting bar to short both control circuits together. Check the connectors



and CPAs if a DTC with symptom byte 02 or 0E is set, to ensure the shorting bars are not causing the circuits to be shorted together. Shorting bars



are used in the locations listed below:



* Passenger instrument panel air bag



* Driver and passenger seat side air bags



* Left and right roof rail air bags



* Driver and passenger seat belt retractor pretensioners



* SDM



* Inline connectors - on the side of the harness connector



* Harness side of the SDM connector



Terminal fretting or incorrectly seated connector can cause an open/high resistance condition. Check the circuit terminals for fretting or incorrectly



seated connector if a DTC with symptom byte 04 or 0D is set. If DTCs of deployment loops which are in the seat DTC B0014 and B0021, can



occur because of stress or damage to the harness due to seat movement. Move the seat to the full extend of travel while using the scan tool to



observe deployment type loop parameters.



If the pretensioner, passenger instrument panel or side air bag has inflated under unexpected conditions and/or DTC with symptom byte 01 is set,



check both control circuits for a short to voltage.



Reference Information



Schematic Reference



SIR Schematics (See: Diagrams/Electrical Diagrams/Air Bag Systems)



Connector End View Reference



Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)



Description and Operation



SIR System Description and Operation (See: Restraints and Safety Systems/Air Bag Systems/Description and Operation/SIR System)



Electrical Information Reference



* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit



Testing/Circuit Testing)



* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General



Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)



* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring



Repairs/Wiring Repairs)



* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic