Showing posts with label 瀚慖f less than the specified range. Show all posts
Showing posts with label 瀚慖f less than the specified range. Show all posts

Wednesday, January 22, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 854

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 854



瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,



replace the K19 suspension control module.



瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K19



suspension control module.



5. Verify the scan tool Vertical Body Acceleration parameter is less than -3 m/s(2).



瀚慖f greater than the specified value, test the signal circuit for a short to ground. If the circuit tests normal, replace the K19 suspension



control module.



6. Install a fused jumper wire between the signal circuit terminal 2 and the low reference circuit terminal 3.



7. Verify the scan tool Vertical Body Acceleration parameter is greater than 3 m/s(2).



瀚慖f less than the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace



the K19 suspension control module.



8. If all circuits test normal, replace the B162 vertical body acceleration sensor.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Electronic Suspension Front Vertical Accelerometer Replacement - Upper (See: Sensors and Switches/Sensors and Switches - Steering and



Suspension/Sensors and Switches - Suspension/Acceleration Sensor/Service and Repair/Electronic Suspension Front Vertical Accelerometer



Replacement - Upper)



* Electronic Suspension Rear Position Sensor Replacement (See: Sensors and Switches/Sensors and Switches - Steering and



Suspension/Sensors and Switches - Suspension/Ride Height Sensor/Service and Repair)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for suspension control module replacement, setup



and programming



C0670



DTC C0670 or C0675



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC C0670 02



- Left Front Acceleration or Position Sensor Circuit Short to Ground



DTC C0670 05



- Left Front Acceleration or Position Sensor Circuit High Voltage/Open



DTC C0670 0A



- Left Front Acceleration or Position Sensor Circuit Too Slow Transitions



DTC C0675 02



- Right Front Acceleration or Position Sensor Circuit Short to Ground



DTC C0675 05



- Right Front Acceleration or Position Sensor Circuit High Voltage/Open



DTC C0675 0A



- Right Front Acceleration or Position Sensor Circuit Too Slow Transitions



Diagnostic Fault Information

Wednesday, January 1, 2020

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 636

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 636



瀚慖f less than the specified range, test either control circuit for a short to ground. If the circuits test normal, replace the X53 fuse block-rear.



瀚慖f greater than the specified range, test either control circuit for a short to voltage or an open/high resistance. If the circuits test normal,



replace the X53 fuse block-rear.



11. If all circuits test normal, replace the K9 BCM.



Component Testing



1. Ignition OFF, disconnect the harness connector at the appropriate A23 door latch assembly.



2. Install a 25 A fused jumper wire between one of the control terminals and 12 V. Momentarily install a jumper wire between the other control



terminal and ground. Reverse the jumper wires at least two times, the A23 door latch assembly should perform the LOCK and UNLOCK



functions.



瀚慖f it does not perform as specified, replace the A23 door latch assembly.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Front Side Door Lock Replacement (See: Body and Frame/Locks/Door Locks/Service and Repair/Front Side Door Lock Replacement)



* Rear Side Door Lock Replacement (See: Body and Frame/Locks/Door Locks/Service and Repair/Rear Side Door Lock Replacement)



* Fuse Block Replacement (See: Maintenance/Fuses and Circuit Breakers/Fuse Block/Service and Repair/Removal and Replacement/Fuse



Block Replacement)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming



B3130



DTC B3125, B3130, or B3135



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC B3125 01



- Driver Door Only Unlock Circuit Short to Battery



DTC B3125 02



- Driver Door Only Unlock Circuit Short to Ground



DTC B3130 01



- All Doors Unlock Circuit Short to Battery



DTC B3130 02



- All Doors Unlock Circuit Short to Ground



DTC B3135 01



- All Doors Lock Circuit Short to Battery



DTC B3135 02



- All Doors Lock Circuit Short to Ground



Diagnostic Fault Information

Friday, December 20, 2019

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 548

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 548



瀚慖f less than the specified range, test the circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K73



telematics communication interface control module.



瀚慖f greater than the specified range, test the circuit for a short to voltage. If the circuit tests normal, replace the K73 telematics



communication interface control module.



4. If all circuit test normal, replace the B24 cellular phone microphone.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Mobile Telephone Microphone Replacement (See: Accessories and Optional Equipment/Cellular Phone/Cellular Phone Microphone/Service



and Repair)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for telematics communication interface control



module replacement, setup, and programming



B2462



DTC B2462 (OnStar/Navigation GPS Antenna)



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC B2462 01



- Global Positioning System Short to Battery



DTC B2462 02



- Global Positioning System Short to Ground



DTC B2462 04



- Global Positioning System Open



Circuit/System Description



The cellular phone, navigation, and digital radio antenna is connected to the telematics communication interface control module. This module



supplies 5 V to the cellular phone, navigation, and digital radio antenna to power the internal amplifier. When the vehicle is equipped with the



optional navigation radio, a navigation signal splitter is installed to distribute the GPS signal to both the telematics communication interface control



module and the navigation radio. The navigation radio supplies 5 V through the GPS antenna coaxial cable to the navigation signal splitter to power



the internal navigation radio signal amplifier.



Conditions for Running the DTC



Onstar - Telematics Communication Interface Control Module



* Ignition is in the RUN or ACC position.



* System voltage is greater than 9 V and less than 16 V.



* The above conditions are present for greater than 1 second.



Navigation Radio



* Radio On.



* System voltage is greater than 9 V and less than 16 V.



* The navigation radio tests the GPS antenna every 10 seconds.



Conditions for Setting the DTC



B2462 01



The telematics communication interface control module and/or the navigation radio detect a short to B+ on the GPS antenna signal circuit.

Tuesday, December 3, 2019

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 639

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 639



瀚慖f less than the specified range, test either control circuit for a short to ground. If the circuits test normal, replace the X53 fuse block-rear.



瀚慖f greater than the specified range, test either control circuit for a short to voltage or an open/high resistance. If the circuits test normal,



replace the X53 fuse block-rear.



11. If all circuits test normal, replace the K9 BCM.



Component Testing



1. Ignition OFF, disconnect the harness connector at the appropriate A23 door latch assembly.



2. Install a 25 A fused jumper wire between one of the control terminals and 12 V. Momentarily install a jumper wire between the other control



terminal and ground. Reverse the jumper wires at least two times, the A23 door latch assembly should perform the LOCK and UNLOCK



functions.



瀚慖f it does not perform as specified, replace the A23 door latch assembly.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Front Side Door Lock Replacement (See: Body and Frame/Locks/Door Locks/Service and Repair/Front Side Door Lock Replacement)



* Rear Side Door Lock Replacement (See: Body and Frame/Locks/Door Locks/Service and Repair/Rear Side Door Lock Replacement)



* Fuse Block Replacement (See: Maintenance/Fuses and Circuit Breakers/Fuse Block/Service and Repair/Removal and Replacement/Fuse



Block Replacement)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming



B3135



DTC B3125, B3130, or B3135



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC B3125 01



- Driver Door Only Unlock Circuit Short to Battery



DTC B3125 02



- Driver Door Only Unlock Circuit Short to Ground



DTC B3130 01



- All Doors Unlock Circuit Short to Battery



DTC B3130 02



- All Doors Unlock Circuit Short to Ground



DTC B3135 01



- All Doors Lock Circuit Short to Battery



DTC B3135 02



- All Doors Lock Circuit Short to Ground



Diagnostic Fault Information

Friday, November 8, 2019

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 642

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 642



瀚慖f less than the specified range, test either control circuit for a short to ground. If the circuits test normal, replace the X53 fuse block-rear.



瀚慖f greater than the specified range, test either control circuit for a short to voltage or an open/high resistance. If the circuits test normal,



replace the X53 fuse block-rear.



11. If all circuits test normal, replace the K9 BCM.



Component Testing



1. Ignition OFF, disconnect the harness connector at the appropriate A23 door latch assembly.



2. Install a 25 A fused jumper wire between one of the control terminals and 12 V. Momentarily install a jumper wire between the other control



terminal and ground. Reverse the jumper wires at least two times, the A23 door latch assembly should perform the LOCK and UNLOCK



functions.



瀚慖f it does not perform as specified, replace the A23 door latch assembly.



Repair Instructions



Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.



* Front Side Door Lock Replacement (See: Body and Frame/Locks/Door Locks/Service and Repair/Front Side Door Lock Replacement)



* Rear Side Door Lock Replacement (See: Body and Frame/Locks/Door Locks/Service and Repair/Rear Side Door Lock Replacement)



* Fuse Block Replacement (See: Maintenance/Fuses and Circuit Breakers/Fuse Block/Service and Repair/Removal and Replacement/Fuse



Block Replacement)



* Control Module References (See: Testing and Inspection/Programming and Relearning) for BCM replacement, setup, and programming



B3140



DTC B3140 or B3150



Diagnostic Instructions



* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System



Check - Vehicle) prior to using this diagnostic procedure.



* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an



overview of the diagnostic approach.



* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure



Instructions) provides an overview of each diagnostic category.



DTC Descriptors



DTC B3140 00



- Driver Unlock Switch Circuit



DTC B3150 00



- Driver Lock Switch Circuit



Diagnostic Fault Information



Circuit/System Description



The body control module (BCM) monitors the voltage level of the door lock and door unlock signal circuits. When the central door lock switch is



in the open position, the voltage level in the signal circuit will be near 0 V. When the central door lock switch is pressed to the lock or unlock



position, a signal will be sent to the BCM requesting a lock or unlock command.



Conditions for Running the DTC



The system voltage is 9-16 V.



Conditions for Setting the DTC