2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 347

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 347

瀚慖f not the specified value, replace the S79RR window switch-right rear.

4. Command the driver window to go UP, DOWN, express UP and express DOWN by using the S79D window switch-driver. The driver

window should perform the UP, DOWN, express UP and express DOWN functions.

瀚慖f the driver window does not perform as specified, refer to Driver Window Switch Malfunction.

5. Command the passenger window to go UP, DOWN, express UP and express DOWN by using the S79P window switch-passenger. The

passenger window should perform the UP, DOWN, express UP and express DOWN function.

瀚慖f the passenger window does not perform as specified, refer to Passenger Window Malfunction.

Circuit/System Testing

Driver Window Switch Malfunction

1. Ignition OFF, disconnect the harness connector at the S79D window switch-driver.

2. Ignition ON, verify that the scan tool Driver Window Main Control Down Switch parameter is Inactive.

瀚慖f not the specified value, test the control circuit terminal 3 for a short to ground. If the circuit tests normal, test or replace the M74D

window motor-driver.

3. Verify that the scan tool Driver Window Main Control Up Switch parameter is Inactive.

瀚慖f not the specified value, test the control circuit terminal 6 for a short to ground. If the circuit tests normal, test or replace the M74D

window motor-driver.

4. Verify that the scan tool Driver Window Main Control Express Switch parameter is Inactive.

瀚慖f not the specified value, test the control circuit terminal 2 for a short to ground. If the circuit tests normal, test or replace the M74D

window motor-driver.

5. If all circuits test normal, test or replace the S79D window switch-driver.

Passenger Switch Window Malfunction

1. Ignition OFF, disconnect the harness connector at the S79P window switch-passenger.

2. Ignition ON, test for greater than 10V between the signal circuit terminal listed below and ground:

* Signal circuit terminal 6

* Signal circuit terminal 7

* Signal circuit terminal 8

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, test or

replace the M74P window motor-passenger.

3. If all circuits test normal, test or replace the S79P window switch-passenger.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Front Side Door Window and Multifunction Switch Replacement (See: Windows and Glass/Windows/Service and Repair/Front Side Door

Window and Multifunction Switch Replacement)

* Rear Side Door Window Switch Replacement (See: Windows and Glass/Windows/Service and Repair/Rear Side Door Window Switch

Replacement)

* Rear Side Door Window Regulator Motor Replacement (See: Windows and Glass/Windows/Service and Repair/Rear Side Door Window

Regulator Motor Replacement)

B324A

DTC B324A

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions)provides an overview of each diagnostic category.

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 338

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 338

瀚慖f not the specified value, test the control circuit terminal 3 for a short to ground. If the circuit tests normal, test or replace the M74D

window motor-driver.

3. Verify that the scan tool Driver Window Main Control Up Switch parameter is Inactive.

瀚慖f not the specified value, test the control circuit terminal 6 for a short to ground. If the circuit tests normal, test or replace the M74D

window motor-driver.

4. Verify that the scan tool Driver Window Main Control Express Switch parameter is Inactive.

瀚慖f not the specified value, test the control circuit terminal 2 for a short to ground. If the circuit tests normal, test or replace the M74D

window motor-driver.

5. If all circuits test normal, test or replace the S79D window switch-driver.

Passenger Switch Window Malfunction

1. Ignition OFF, disconnect the harness connector at the S79P window switch-passenger.

2. Ignition ON, test for greater than 10V between the signal circuit terminal listed below and ground:

* Signal circuit terminal 6

* Signal circuit terminal 7

* Signal circuit terminal 8

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, test or

replace the M74P window motor-passenger.

3. If all circuits test normal, test or replace the S79P window switch-passenger.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Front Side Door Window and Multifunction Switch Replacement (See: Windows and Glass/Windows/Service and Repair/Front Side Door

Window and Multifunction Switch Replacement)

* Rear Side Door Window Switch Replacement (See: Windows and Glass/Windows/Service and Repair/Rear Side Door Window Switch

Replacement)

* Rear Side Door Window Regulator Motor Replacement (See: Windows and Glass/Windows/Service and Repair/Rear Side Door Window

Regulator Motor Replacement)

B317A

DTC B316B, B317A, B318A, or B319A

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B316B 00

- Driver Window Switch

DTC B316B 02

- Driver Window Switch Short to Ground

DTC B316B 39

- Driver Window Switch Internal Malfunction

DTC B317A 02

- Passenger Window Switch Short to Ground

DTC B317A 39

- Passenger Window Switch Internal Malfunction

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 363

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 363

瀚慖f not the specified value, test the signal circuit terminal 4 for a short to ground. If the circuit tests normal, replace the K39 liftgate control

module.

4. Install a 3 A fused jumper wire between the signal circuit terminal 4 and ground. Verify the scan tool Liftgate Front Control Switch

parameter is Active.

瀚慖f not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the

K39 liftgate control module.

5. If all circuits test normal, test or replace the S45B liftgate control switch-interior.

Component Testing

1. Ignition OFF, disconnect the harness connector at the S45B liftgate control switch-interior.

2. Test for the values listed below between the signal terminal 3 and the ground terminal 1.

* 600-650 ohm in the Off position

* 125k-140k ohm in the 3/4 position

* 400k-415k ohm in the Max position

瀚慖f not within the specified ranges, replace the S45B liftgate control switch-interior.

3. Test for infinite resistance between the signal terminal 4 and the ground terminal 1 with the switch open.

瀚慖f not the specified value, replace the S45B liftgate control switch-interior.

4. Test for less than 3 ohm between the signal terminal 4 and the ground terminal 1 with the switch closed.

瀚慖f greater than the specified range, replace the S45B liftgate control switch-interior.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.

* Liftgate Actuator Control Switch Replacement (See: Body and Frame/Doors, Hood and Trunk/Trunk / Liftgate/Trunk / Liftgate

Motor/Service and Repair)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for the liftgate control module replacement, setup

and programming

B396D

Liftgate Interior Release Open/Close Switch Malfunction - DTC B396C or B396D

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC B396C 08

- Liftgate Mode Switch Circuit Performance Signal Invalid

DTC B396D 02

- Front Liftgate Actuator Switch Circuit Short To Ground

Diagnostic Fault Information

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 947

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 947

瀚慖f not the specified value, replace the Q6 Camshaft Position Actuator Solenoid Valve.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Intake (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 1 (Right Side) Intake)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Intake (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 2 (Left Side) Intake)

* Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust (See: Engine, Cooling and

Exhaust/Engine/Actuators and Solenoids - Engine/Variable Valve Timing Solenoid/Service and Repair/Camshaft Position Actuator Solenoid

Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for Engine Control Module replacement, setup, and

programming

P013A

DTC P0133, P013A, or P013E (Without LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0133

- HO2S Slow Response Sensor 1

DTC P013A

- HO2S Slow Response Rich to Lean Sensor 2

DTC P013E

- HO2S Delayed Response Rich to Lean Sensor 2

Diagnostic Fault Information

Circuit Description

The heated oxygen sensors (HO2S) are used for fuel control and catalyst monitoring. Each HO2S compares the oxygen content of the surrounding

air with the oxygen content of the exhaust stream. When the engine is started, the control module operates in an Open Loop mode, ignoring the

HO2S signal voltage while calculating the air-to-fuel ratio. The control module supplies the HO2S with a reference, or bias voltage of about 450

mV. While the engine runs, the HO2S heats up and begins to generate a voltage within a range of 0-1,000 mV. This voltage will fluctuate above

and below the bias voltage. Once sufficient HO2S voltage fluctuation is observed by the control module, Closed Loop is entered. The control

module uses the HO2S voltage to determine the air-to-fuel ratio. An HO2S voltage that increases above bias voltage toward 1,000 mV indicates a

rich fuel mixture. An HO2S voltage that decreases below bias voltage toward 0 mV indicates a lean fuel mixture.

The heating elements inside each HO2S heat the sensor to bring the sensor up to operating conditions faster. This allows the system to enter Closed

Loop earlier and the control module to calculate the air-to-fuel ratio sooner.

Conditions for Running the DTCs

* Before the ECM can report that DTC P0133, DTCs P0030, P0031, P0032, and P0135 must run and pass.