2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 431

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 431

Control Module References (See: Testing and Inspection/Programming and Relearning) for radio/HVAC control replacement, setup, and

programming

B1023

DTC B1023

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC B1023 00

- Integral Switch Malfunction

Circuit/System Description

The vehicle theft deterrent subsystem provides the capability to lock or unlock the steering electrically. The steering column lock control module is

allowed to unlock when power mode transitions to a non off power mode and an authenticated driver identification device is present. Once the

column is unlocked, a crank request can be allowed.

Conditions for Running the DTC

* The ignition is in OFF, ACCESSORY or RUN position.

* The system voltage is between 9-16 V.

Conditions for Setting the DTC

The steering column lock control module detects an internal sensor malfunction resulting in lock status of invalid to be transmitted on serial data.

Action Taken When the DTC Sets

* DTC B1023 is stored in memory.

* The driver information center displays the service column lock system warning message.

* The steering column lock indicator is ON.

Conditions for Clearing the DTC

* No steering column lock control module internal sensor malfunction so lock status of valid is transmitted on serial data.

* The condition for setting the DTC is no longer present.

Reference Information

Schematic Reference

Column Lock Schematics (See: Diagrams/Electrical Diagrams/Steering/Steering Column)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Steering Wheel and Column Description and Operation (See: Steering and Suspension/Steering/Steering Column/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 471

2010 Cadillac Truck SRX AWD V6-2.8L Turbo Page 471

* Control Module References (See: Testing and Inspection/Programming and Relearning)for BCM replacement, setup, and programming

B1480

DTC B1480

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions)provides an overview of each diagnostic category.

DTC Descriptor

DTC B1480 02

- Battery Rundown Protection Circuit Short to Ground

Diagnostic Fault Information

Circuit/System Description

The battery saver mode reduces the parasitic load of some modules during overseas shipment or during vehicle storage conditions. This improves

the drain time on the battery of up to 70 days without the battery going dead. When the vehicle is in transport/storage, some features may have

reduce functionality as a result being in the battery saver mode, such as disabling the Remote Function Actuator or content theft features.

The battery saver mode incorporates a latching relay that when enabled disconnects some modules from their ignition off power or memory power

sources. Battery saver mode is initiated by starting the vehicle and then turning the ignition key into the crank position for greater than 15 seconds.

The mode is disengaged by repeating the previous process causing the relay to latch in the other direction. This feature can be used as many times

as necessary if the vehicle is to be stored for an extended period of time.

Conditions for Running the DTC

* The system voltage is between 9-16 V.

* The DTC can only run when the output is activated.

Conditions for Setting the DTC

The BCM detects a short to ground in the battery saver relay set circuit.

Action Taken When the DTC Sets

The module output driver will be shut down and not supply voltage to the battery saver relay set circuit.

Conditions for Clearing the DTC

* The current DTC will clear when the module request for the output is removed or the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

Reference Information

Schematic Reference

* Body Control System Schematics (See: Body and Frame/Body Control Systems/Diagrams/Electrical Diagrams)

* Power Distribution Schematics (See: Diagrams/Electrical Diagrams/Starting and Charging/Power and Ground Distribution/System

Diagram/Power Distribution Schematics)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Power Mode Description and Operation (See: Power and Ground Distribution/Description and Operation/Power Mode)

Electrical Information Reference